Getting Started With xTool D1 Pro

por Shopify API Publicado en May 12, 2023
how to use xtool d1 pro

So many people build the laser and then lay an expensive piece of wood down, or even worse, a $40 Yeti cup only to watch as the text or logo they want to apply starts engraving upside down and backwards. 

The user forums are full of such sad tales. And if you read the user forums long enough you’ll see this: “I only left the room for a minute, and then the fire started”.

It’s important to jump into this endeavor patiently, and responsibly.

Read the manual and watch assembly videos before assembling your machine

Double check all electronics connectors prior to powering up

Plan on assembly taking an hour or two. Before you connect to the machine take a quick assessment of what you’ve done and reinspect that all the electrical connectors are properly installed and seated correctly. The user forums are also full of “my machine only goes back and forth and not up and down” posts as well. 

Before you connect to a computer you need to ensure that you have a piece of scrap wood or thick cardboard laying under the machine. Push the wrong button and engrave the top of your wife’s dinner table and you’ll be dead meat. 

Start with the xTool Creative Space software

xtool d1 pro firmware update

Check and upgrade firmware

Before you even think about beginning a project you should get a piece of scrap wood or thick cardboard and start simple by engraving a single letter or a number. 

Ensure the machine size (Laser Flat) is selected

Set the Output to “Score” and use low power and quicker speeds. Ensure the machine size is set correctly as well. The example is set to “Laser Flat”. 

laser engraved leather wallet

In the example above we have used 20% power and 60 mm/sec speed. Ensure you have the material to be marked under the laser and that the laser is focused properly by using the built in focus tool.

Then hit the Process button on the bottom righthand corner.

Now we’ll Frame our letter T and that will send the laser head to where the T is located in the workspace. Right at this moment we don’t care where that location is. We just want to test our machine.

laser engraved leather wallet

When you hit the Framing button it will instruct you to push the button on top of your xTool D1 Pro. Then the framing operation will begin. You can do this as many times as you need to. 

Once you have determined that your material to engrave is under where the laser framing operation is then you can hit the “Start” button in the top righthand corner. Once again you will be prompted to hit the button the xTool D1 Pro to begin. Make sure you have your laser safety glasses on. 

Play around with different speed and power settings

Depending on what material you have under the laser, 20% power and 60 mm/sec speed may barely score your material. If you can’t see your “T” then try 25% power and 55 mm/sec speed. Keep doing this until you get the results that YOU want to see.

Once you have become the Master of The “T” then it is time to move on to something more complicated like the entire word “TEST”. Then from scoring the letters you can set them to engrave which will fill in the letters. As always, start with low power and fast speed.

Test on different materials

If you started with a piece of cardboard, now it is time to move on to a piece of scrap wood. Again, start with low power and faster speeds and slowly dial the settings to achieve the look you are shooting for.  

You may think that what is discussed next should have been mentioned first, but you’d be wrong. You need to develop a rudimentary understanding of how different speeds and power settings affect both scoring and engraving different materials before you use some reference settings. Without this basic understanding you are setting yourself up for failure. 

Try xTool Reference settings

Under your setup, on the main page of XCS there is a dropdown box for “Material”. As an example “Cherry Plywood” has been selected.

This auto fills your power setting at 50% and sets your speed at 30 mm/sec.

These settings come from the xTool Selected Reference and while they might score and engrave perfectly, the new user should consider them to be good starting points.

Play around on a piece of scrap Cherry Plywood (or whatever material you have selected) and make MINOR adjustments in the speeds and power settings. 

This way you will achieve the look that is most appealing to you.

I strongly encourage all new users to take this, or a similar approach to getting started.

For more questions. Please join our Facebook group to get inspired!